Investigasi Kekakuan Pada Pelat Baja Lunak Dengan Pembentukan Metode Dimple Dies Triangle Profile
DOI:
https://doi.org/10.33504/jitt.v4i1.403Keywords:
Dimple Dies, Natural Frequency, Plate Stiffness, Taguchi, Vibroport 80Abstract
This study aims to analyze the effect of variations in the number and diameter of dimple holes on the stiffness of mild steel plates using the Dimple Dies Triangle Profile forming method. Plate stiffness is important for reducing vibrations, especially in vehicle components. The material used was a 0.6 mm thick galvanneal plate, with dimple diameters of 25 mm and 30 mm, and hole quantities of 16 and 20. Testing was conducted using a Vibroport 80 device to measure natural frequency as an indicator of stiffness. The experimental design employed the Taguchi method with an L4 orthogonal array to analyze the influence of each parameter. The results showed that the number of dimple holes significantly affected the plate’s natural frequency, while the dimple diameter had no significant effect. The optimal combination producing the highest stiffness was a 25 mm dimple diameter with 16 holes. ANOVA and S/N ratio analysis supported these findings, indicating that the number of holes contributed more than 90% to the variation. This research is expected to serve as a reference for developing stiffer and more vibration-resistant metal plate designs, particularly for automotive and other engineering structure applications.
Downloads
References
N. E. &. B. H. A. Yuspian Gunanwan, "Analisa Pengaruh Pengelasan Listrik Terhadap Sifat Mekanik Baja Karbon Rendah Dan Baja Karbon Tinggi," ENTHALPY-Jurnal Ilmiah Mahasiswa Teknik Mesin, pp. 1-12, 2017.
A. I. A. &. E. Abimanyu Harsono, "Pengaruh Pembentukan Alur Trapesium Pada Pelat Galvanil dengan Proses Bead Roller Terhadap Frekuensi Alami Pada Kondisi Batas Jepit – Jepit," Jurnal Teknik Mesin, pp. 183-188, 2024.
E. Febian M Fadillah, "Analisis Kekakuan Pelat Baja Galvanil Ketebalan 0,6 MM Akibat Pembentukan Dengan Metode Bead Rolled," Manutech : Jurnal Teknologi Manufaktur, pp. 228-232, 2024.
N. Endriatno, "Penentuan Frekuensi Pribadi Balok Kantilever Pada Dimensi Yang Berbeda," Dinamika : Jurnal Ilmiah Teknik Mesin, pp. 71-76, 2020.
S. Lubis, "Simulasi Getaran Pada Piringan Tunggal Akibat Perubahan Putaran," SiNTESa : Seminar Nasional Teknologi Edukasi dan Humaniora, pp. 1-7, 2021.
T. Rokhman, "Analisis Getaran Pada Footrest Sepeda Motor Tipe Matic dan Non-Matic," Jurnal Ilmiah Teknik Mesin, pp. 31-40, 2016.
E. Sukanto, "Pengaruh Perlakuan Panas Pada Pembentukan Pelat Beralur Panel Kendaraan Terhadap Peningkatan Frekuensi Alamiah Diukur Pada Kondisi Batas Jepit-Jepit," Jurnal Rotor, pp. 1-6, 2016.
S. &. E. Edwira Nurazizi Aulia, "Pengaruh Pengerolan Alur Pelat Heksagonal Terhadap Frekuensi Pribadinya Dalam Kondisi Bebas-Bebas," Jurnal Inovasi Teknologi Terapan, pp. 292-299, 2023.
S. &. E. Marcel Darensyah, "Pengaruh Pengerolan Pelat Kondisi Dingin Terhadap Kekakuan Pelat Pada Bak Mobil Pick Up," Jurnal Inovasi Teknologi Terapan, pp. 107-113, 2023.
E. &. F. A. M. Irfan Nur Kholis, "Analisa Kekakuan Pelat terhadap Pembentukan Dimple Dies dengan Variasi Diameter Lubang dan Jumlah Lubang Dimple," Jurnal Inovasi Teknologi Terapan, pp. 194-200, 2024.
L. A. N. Wibawa, "Analisis Frekuensi Natural Rangka Main Landing Gear Pesawat UAV Menggunakan Ansys Workbench," Jurnal Mesin Nusantara, Vol. 5,No. 1, pp. 65-73, 2022.
P. H. &. Y. Ekawati, "Penerapan Metode Taguchi untuk Meningkatkan Kualitas Bata Ringan pada UD. XY Malang," Journal of Industrial Engineering and Management Systems Vol. 13, No. 1, pp. 13-26, 2020.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
