Pengaruh Kecepatan Pemotongan, Feed Rate Dan Depth Of Cuth Terhadap Kekasaran Permukaan Pada Benda Kerja Material S45C Pada Proses CNC Milling
DOI:
https://doi.org/10.33504/jitt.v4i2.410Keywords:
CNC milling, surface roughness, S45C steel, Respon Surface Methodology (RSM), Machining ParamatersAbstract
Surface quality is an important aspect in machining processes because it affects the performance and service life of components. S45C steel is widely used in the automotive and manufacturing industries, thus optimization of cutting parameters is required to obtain the best surface quality. Each machining parameter has a different level of influence on machining results. Therefore, this study was conducted to analyze the effects of cutting speed, feed rate, and depth of cut on surface roughness as well as to determine the optimum parameter combination in the CNC milling of S45C steel. The Response Surface Methodology (RSM) with a Box–Behnken design was used to develop the experimental plan consisting of 15 combinations. Surface roughness measurements were carried out using a Mitutoyo SJ-210. Analysis of variance (ANOVA) showed that depth of cut significantly affected surface roughness with a P-value < 0.05, while cutting speed and feed rate did not exhibit a statistically significant effect. The developed second-order regression model resulted in a saddle point characteristic, indicating that the optimum value was not located at either the lower or upper limit of the parameters. The optimization results indicate optimum conditions at a cutting speed of 82.85 m/min, feed rate of 298 mm/min, and depth of cut of 0.87 mm with a predicted surface roughness of 2.56 µm. These findings can serve as a reference for setting machining parameters to improve the surface quality of S45C steel.
Downloads
References
I. Prakoso, “Analisa Pengaruh Kecepatan Feeding Terhadap Kekasaran Permukaan Draw Bar Mesin Milling Aciera.,” Jurnal Teknik Mesin (Journal Of Mechanical Engineering), vol. 3, no. 3, pp. 1-6, 2017.
A. M. dan S. R. , “Optimalisasi Parameter Mesin CNC Milling 3 Axis terhadap Waktu Produksi. Formosa Journal of Applied Sciences,,” 2022.
C. H. &. Y. “Analisa Kekasaran Permukaan Terhadap Kekerasan Material Pada Proses Milling Dengan Variasi Kecepatan Feeding,” Jurnal Teknik Mesin, 2019.
K. D. A. &. Y. D. “Analisis Variasi Nilai Depth of Cuth Terhadap Kekasaran Permukaan pada Material S45C Menggunakan Pahat Ball nose End Mill,” JURNAL TEKNIK MESIN, pp. 30-35, 2023.
M. e. al, “Response Surface Methodology: Process and Product Optimization Using Designed Experiments,” 2020.
W. p. andika, H. dan M. Yunus, “Analisis Kekasaran Permukaan Pemotongan Sisi Gerak,” p. 7, 2024.
M. Fahmi, “Surface Roughness Measurement Using Stylus Profilometer and Its Correlation with Surface Morphology and Tribological Performance,” Journal of Physics: Conference Series, 2023.
D. A. Kirana dan D. Yuhas, “Analisis Variasi Nilai Depth of Cuth Terhadap Kekasaran Permukaan pada Material S45C Menggunakan Pahat Ball nose End Mill,” TEKNIK MESIN, pp. Hal 30-35, 2022.
Y. Prayoga, J. Jufriadi dan M. Mawardi , “Analisa Pengaruh Variasi Kedalaman Pemakanan Terhadap Kekasaran Permukaan Proses Frais,” Jurnal Mesin Sains Terapan, pp. 19-22, 2020.
A. Priyatmojo dan R. , “Pengaruh Kecepatan Spindle dan Kedalaman Pemakanan Proses CNC Frais terhadap kekasaran Permukaan Remelting Blok Silinder,” Jurnal Kompetensi Teknik, pp. 25-29, 2019.
,. I. Rachmanta, “Pengaruh Parameter Pemotongan Terhadap Kekasaran Permukaan Baja Karbon Rendah pada Proses Conventional Menggunakan Pahat End Mill,” Jurnal Teknik Mesin,, pp. 1-13, 2020.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
