Analisis Pengaruh Sudut Mata Potong Bahan S55C Tipe Flate Terhadap Hasil Cacahan Plastik
DOI:
https://doi.org/10.33504/jitt.v3i1.291Keywords:
Cutting Egde, Experimentation, Plastic, ShredderAbstract
Manage bottle waste in the surrounding environment very important. Therefore, a plastic chopping machine was created which is expected to optimize this problem. One of the most important components in plastic chopping machines is the cutting edge, the cutting edge of the plastic chopping machine plays an important role in the chopping process. The cutting edge used in this study is made from flate-type S55C steel with a cutting edge inclination angle of 25˚ and 35˚. The purpose of this study is to determine the quality of the results of plastic waste shredding against S55C steel cutting edge material, determine the effect of cutting edge angle with angle variations of 25˚ and 35˚ on the results of plastic waste shredding, knowing the angle of the cutting edge that is good for the plastic shredding process. The method used in this research uses experimental methods. The results of this study indicate that the 35˚ angle cutting edge within one minute produces more shreds than the 25˚ angle cutting edge but for the size of the shreds from both cutting edges have the same length and width variations ranging from one to twenty millimeters.
Downloads
References
Madanih, R., Anindita, A., & Kurnia, A. Indonesia Darurat Limbah Plastik: Merubah Limbah Botol Plastik Menjadi Kursi Multiguna Di Kelurahan Sawah Baru, Ciputat, Tangerang Selatan. In Prosiding Seminar Nasional Pengabdian Masyarakat LPPM UMJ, 2019.
Komang Winarti, N., Patriono, G., Adelia, E., Kristanti, N., Antropologi, P., Ips, P., & Guru Sekolah Dasar, P. Ilmu Sosial, F., & Ilmu Pendidikan, F. Pemanfaatan Botol Plastik Bekas menjadi Barang yang Bernilai Guna (Tempat Sampah). Journal Lepa-Lepa Open, 1(5), 1001-1013, 2022.
Fabiani, V. A. (Edukasi dan Sosialisasi Pengelolaan Sampah Plastik pada KSM Srimenanti Jaya Sungailiat Bangka. Empowerment: Jurnal Pengabdian Masyarakat, 1(4), 630-636, 2022.
Hendra, H., Al Qirom, S., Susilo, S., Nugraha, K., Hernadewita, H., & Hardian, F. Analisa Tegangan pada Desain Empat Mata Potong untuk Mesin Pencacah Plastik Menggunakan Metode Elemen Hingga. Jurnal Teknik Mesin, 16(2), 118-126, 2023.
Saputra, S. R., Nurrohkayati, A. S., Nugroho, A., & Waloyo, H. T. Pengaruh besar sudut potong mata pisau tipe flate terhadap hasil cacahan plastik pada mesin pencacah. TEKNOSAINS: Jurnal Sains, Teknologi dan Informatika, 10(1), 30-37, 2023.
Annas Dzar, A. G., Yuda, F., & Leo, S. RANCANG BANGUN MESIN PENCACAH SAMPAH PLASTIK UNTUK MESIN INJEKSI PLASTIK DI POLMAN BABEL (Doctoral dissertation, Politeknik Manufaktur Negeri Bangka Belitung), 2023.
Anantanur, D., Setyoko, B., & Murni, M. ANALISA STRUKTUR MIKRO DAN KEKERASAN PADA BAJA S55C SETELAH DILAKUKAN PROSES TEMPERING. Jurnal Mekanova: Mekanikal, Inovasi dan Teknologi, 9(1), 77-83, 2023.
Yulianto, E. S., Yuniardi, D., Harfit, A. R., & Setyawan, C. A. ANALISIS PULLEY PADA MESIN PENCACAH KALENG BERBANTUAN SOFTWARE SOLIDWORKS. Jurnal Ilmiah Teknik, 3(2), 49-61, 2024.
Van Harling, V. N., & Apasi, H. Perancangan Poros Dan Bearing Pada Mesin Perajang Singkong. Soscied, 1(2), 42-48, 2018.
Arifin, Z. Metodologi penelitian pendidikan. Jurnal Al-Hikmah, 1(1), 2020.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
