Pengaruh Bentuk Geometri terhadap Laju Korosi Baja Karbon dalam Larutan NaCl 3,5%
DOI:
https://doi.org/10.33504/jitt.v4i1.440Keywords:
Corrosion, Geometry, Crevice Corrosion, Carbon Steel, 3,5% NaClAbstract
The geometry of metal components is an important factor influencing corrosion behavior, particularly localized corrosion. This study aims to analyze the effect of geometric variations on the corrosion rate of carbon steel through a simulated laboratory experimental approach. Carbon steel specimens were fabricated with three different geometries, namely flat surface, sharp-edged surface, and crevice geometry. Corrosion testing was conducted using immersion and potentiodynamic polarization methods in a 3.5% NaCl solution. The analyzed parameters included mass loss corrosion rate, corrosion potential, and corrosion current density. The results showed that crevice specimens exhibited the highest corrosion rate, followed by sharp-edged specimens, while flat surfaces demonstrated the best corrosion resistance. This behavior is attributed to the formation of differential aeration cells and non-uniform current density distribution caused by geometric variations. These findings highlight the importance of considering geometric design in corrosion mitigation strategies for metal components.
Downloads
References
P. R. Roberge, Corrosion Engineering: Principles and Practice, New York: McGraw-Hill, 2008.
M. G. Fontana, Corrosion Engineering, 3rd ed., New York: McGraw-Hill, 1986.
B. N. Popov, Corrosion Engineering: Principles and Solved Problems, Oxford: Elsevier, 2015.
A. Turnbull and L. Zhou, “Effect of geometry and crevice conditions on localized corrosion of carbon steel in chloride environments,” Corrosion Science, vol. 165, pp. 108–117, 2020.
M. Y. Nazari, M. R. Amini, and A. Davoodi, “Influence of geometric discontinuities on localized corrosion behavior of steel,” Journal of Materials Engineering and Performance, vol. 29, no. 4, pp. 2456–2464, 2020.
J. Hou, X. Li, and Y. Cheng, “Role of differential aeration induced by geometry on corrosion behavior of pipeline steel,” Electrochimica Acta, vol. 354, pp. 136–145, 2020.
S. Fajardo and J. M. Bastidas, “Effect of crevice geometry on corrosion mechanisms of carbon steel in NaCl solution,” Materials and Corrosion, vol. 72, no. 5, pp. 789–798, 2021.
A. Turnbull, “Localized corrosion associated with geometric effects in carbon steel structures,” in Proceedings of the International Corrosion Conference (CORROSION), NACE International, Houston, TX, USA, 2019, pp. 1–10.
M. R. Amini and A. Davoodi, “Electrochemical study of geometry-induced corrosion in steel structures,” in Materials Today: Proceedings, vol. 42, Elsevier, 2021, pp. 245–251.
R. W. Revie and H. H. Uhlig, Corrosion and Corrosion Control, 4th ed., Hoboken, NJ: John Wiley & Sons, 2008.
K. Zhang, Y. Wu, and X. Chen, “Electrochemical investigation of crevice corrosion influenced by structural geometry in carbon steel,” Journal of Electroanalytical Chemistry, vol. 907, pp. 116–124, 2022.
D. A. Jones, Principles and Prevention of Corrosion, 2nd ed., Upper Saddle River, NJ: Prentice Hall, 1996.
L. Wang, Z. Liu, and H. Luo, “Experimental study on geometry-induced localized corrosion of steel in marine environments,” Ocean Engineering, vol. 234, pp. 109–118, 2021.
S. Fajardo, J. M. Bastidas, and M. Morcillo, “Influence of crevice geometry on corrosion mechanisms of carbon steel in chloride media,” in IOP Conference Series: Materials Science and Engineering, vol. 480, no. 1, IOP Publishing, 2019, pp. 1–7.
L. Wang and Z. Liu, “Effect of geometric discontinuities on localized corrosion behavior of pipeline steel,” in Proceedings of the International Conference on Materials, Metallurgy and Corrosion, IEEE, 2020, pp. 55–60.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
