Pengaruh Kedalaman Pemakanan dan Kecepatan Potong pada Pembubutan Finishing Material Baja SKD 11 terhadap Kekasaran Permukaan Benda Bubutan
DOI:
https://doi.org/10.33504/jitt.v2i1.176Keywords:
Full factorial, Surface roughness, SKD 11Abstract
One important factor in achieving good quality value for a product in the machining process is to look at the level of roughness produced in the machining process. This research aims to determine the effect of feed depth and cutting speed on surface roughness. The process variables used in this research are feeding depth (mm) and cutting speed (m/min). Each variable has 3 levels, namely feeding depth of 0.5, 0.6 and 0.7 mm. Cutting speed 65, 70 and 75 m/min. In this research method, researchers used the full factorial method. The material used in this research is SKD 11 steel. The conclusion obtained from the research is that the minimum surface roughness is at a cutting depth of 0.6 mm with a cutting speed of 65 m/minute, with the average surface roughness value obtained being 0.883 (µm ). The maximum surface roughness is at a feed depth of 0.6 mm with a cutting speed of 70 m/minute with an average surface roughness value of 1.254 (µm).
Downloads
References
N. Hendri Van Hoten1*, Rijalul Rahman Hakim1, Helmizar1, “KARAKTERISTIK KEBULATAN TERHADAP PARAMETER PROSES PEMBUBUTAN PADA MATERIAL ST 42 MENGGUNAKAN METODE TAGUCHI DAN ANOVA ABSTRACT A cylindrical product requires a good roundness value to ensure its quality . One of the factors that determine the quality of t,” vol. 14, no. November, pp. 60–64, 2021.
S. Muhammad Sabil, Ilyas Yusuf, “Pengaruh Variasi Putaran Spindel Dan Kedalaman Pemotongan Terhadap Kekasaran Permukaan,” J. Mesin Sains Terap. Vol.1 No. 1, vol. 1, no. 1, pp. 1–6, 2017.
A. K. E. Mahros Darsin1, Yuni Hermawan1, Hari Arbiantara Basuki1, “Optimasi Kekasaran Dan Kebulatan Permukaan Pada Pembubutan Marmer Dengan Variasi Parameter Kedalaman Potong Kecepatan Potong Dan Gerak Makan,” Response, pp. 13–15, 2010.
Kosjoko, “GEOMETRIK POROS HASIL BUBUT The Depth of Cut Effect on the Roundness Geometry Axis from the Result of the Lathe Machine mesin . Kerusakan tersebut umumnya disebabkan oleh geometrik poros . Salah satu geometrik poros yang faktorial dengan benda kerja baja,” vol. 3, no. 1, pp. 5–8, 2018.
A. Naufal, “Jurusan teknik mesin fakultas teknik universitas sriwijaya 2018,” 2018.
R. MUH.DARWIS, RAMLI, “1 , 2 , 3,” vol. 2, no. 2, 2022.
D. P. Dudung Hermawan1, Dona2, Syahrul Anwar3, “16 https://publikasi.kocenin.com/index.php/teksi,” pp. 16–23, 2022.
Z. Kurniawan, E. Yudo, and R. Rosmansyah, “Optimasi Kekasaran Permukaan Pada Material Amutit Dengan Proses CNC Turning Menggunakan Desain Taguchi,” Manutech J. Teknol. Manufaktur, vol. 10, no. 01, pp. 45–51, 2019, doi: 10.33504/manutech.v10i01.58.
Y. A. E. I. N. H. A. A. dan Y. A. Putra, “Pengaruh Sudut Potong dan Kecepatan Putaran Spindel Terhadap Kekasaran Permukaan pada Proses Bubut Mild Steel ST 37,” vol. 19, no. 2, 2019, doi: 10.24036/invotek.v19i2.582.
R. Mohammad Farokhi1 , Wirawan Sumbodo2, “Jenis Sudut Pahat Pada Proses Pembubutan,” pp. 85–94, 2000.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
