Analisis Kekasaran Permukaan Pemotongan Sisi Gerak Melingkar pada CNC Milling
DOI:
https://doi.org/10.33504/jitt.v2i2.172Keywords:
CNC Milling, Surface Roughness, Taguchi MethodAbstract
Minimal Surface Roughness results are the desired goal in the CNC Milling machining process for circular motion side cutting with the right machining process parameters in order to obtain minimal workpiece Surface Roughness response results. This study was conducted in order to obtain parameters that contribute greatly to surface roughness and determine the effect of parameter variations on the LAGUN MC 750 CNC milling machine using the Taguchi research method. The machining process parameters varied were spindle speed (2,400 RPM, 3000 RPM), depth of feed (0.2 mm, 0.4 mm) and feeding movement (clockwise, counterclockwise) using S45C steel material. The results of this study show that minimal roughness results are obtained with a spindle speed of 2400 RPM, a depth of feed of 0.2 mm, and a counterclockwise feeding movement.
Downloads
References
YONGKI, “ANALISA NILAI KEKASARAN PERMUKAAN MATERIAL BAJA AISI 1040 PADA PROSES PEMESINAN CNC BUBUT MENGGUNAKAN METODE TAGUCHI,” 2022.
M. Yusuf and H. Carles, “Analisa Kekasaran Permukaan Terhadap Kekerasan Material Pada Proses Milling Dengan Variasi Kecepatan Feeding,” Jurnal Teknik Mesin, 2020.
Y. Novrialdy, A. K, Y. A, and F. Prasetya, “Pengaruh Variasi Feed Rate Terhadap Kekasaran Permukaan Polyethylene Mengunakan Mesin Cnc Miiling,” J. Vokasi Mek., vol. 3, no. 2, pp. 25–33, 2021, doi: 10.24036/vomek.v3i2.206.
Y. Yakub and H. Syaifullah, “Analisis Tingkat Kekasaran Permukaan Hasil Proses Milling Pada Baja Karbon S45C,” Semin. Nas. Tek. Mesin, vol. 6, 2015, [Online]. Available: www.qyg1.com/cctrl/news/file/ENDMILL_TAN
A. Mahendra, “Analisis Pengaruh Nilai Parameter Proses Pemesinan Milling Terhadap Kekasaran Tahun 2022,” 2022.
T. S. Allam and W. Sumbodo, “Pengaruh laju Pemakanan dan Kedalaman Potong Pada Proses CNC Turning Terhadap Tingkat Kekerasan Permukaan Baja ST 60,” J. Kompetensi Tek., vol. 12, no. 1, pp. 25–30, 2020.
A. Mashudi and N. A. Susanti, “Pengaruh Media Pendingin dan Kecepatan Putar Spindle Terhadap Hasil Kekasaran Permukaan Benda Kerja Pada Proses Finishing Menggunakan Mesin Bubut CNC PU,” J. Pendidik. Tek. Mesin, vol. 9, no. 3, pp. 57–66, 2020.
F. IRFAN, “Optimasi Parameter 3D Printing Terhadap Bending Stress Pada Astm D-790 Menggunakan Filamen Nylon,” 2023, [Online]. Available: http://repository.polman-babel.ac.id/id/eprint/738/1/TA_IrfanFadhil.pdf
Jondi Supriyandi, “OPTIMASI KEKASARAN PERMUKAAN PROSES CNC TURNING BAJA SKD-11 DENGAN MENGGUNAKAN METODE TAGUCHI Optimizing Surface Roughness Of SKD-11 Steel Lathe Using Taguchi Method Tugas Akhir ini Disusun Untuk Memenuhi Syarat Menyelesaikan Pendidikan Diploma IV Program,” 2021.
D. Prayuda, “PENGARUH SALINITAS PASIR TERHADAP KUAT TEKAN BATA RINGAN,” pp. 1–23, 2016.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
