Optimasi Parameter Proses 3D Printing Terhadap Transparansi Filamen Pla Menggunakan Metode Taguchi
DOI:
https://doi.org/10.33504/jitt.v2i2.161Keywords:
3D Printing, Transparency, The gray taguchi method, PLA filamentsAbstract
3D printing technology is the latest innovation in the world of technology. At the beginning of 3D Printing, technology was known as additive layer. Fused deposition modeling (FDM) technology has been used as rapid prototyping or rapid prototyping with polymers. rapid prototyping with polymers with the material is a filament. filament. The working principle with the FDM step is the layer-by-layer method that uses components such as heat-erosion layer by layer method that uses components such as the heat-er nozzle in this section used to melt the filament that is heated in the process of making the 3D Printer prototype with Fused deposition modeling Ender model with a build size of 180 mm x 300 mm x 300 mm and a single nozzle is used to make research objects using a nozzle with a diameter of 0.4 mm. heater nozzle with a diameter of 0.4 mm, and the filament used is Polylactic Acid (PLA) which is 1.75 mm in diameter, the results of this test are to transparency test using a transparency testing tool, the Lux Meter. In this study using the Taguchi method to produce a more optimal response. where the process parameters such as nozzles, temperature, print speed, and print speed have been determined. temperature, print speed, bed temperature, layer thickness, and temperature-based plate in this study the resulting test Transparency level the highest was 223.667 and the lowest was 100.667 which is where this test using transparent PLA filament, the results of this study will be used for the manufacture of cup products.
Downloads
References
P. Pristiansya and H. Herianto, “Pengaruh Parameter 3D Printing Terhadap Transparansi Produk yang Dihasilkan,” in Prosiding SEMNAS INOTEK (Seminar Nasional Inovasi Teknologi), 2018, pp. 181–186.
A. A. Setiawan, B. W. Karuniawan, and N. Arumsari, “Optimasi parameter 3D printing terhadap keakuratan dimensi dan kekasaran permukaan produk menggunakan metode Taguchi Grey Relational Analysis,” in Proceedings Conference on Design Manufacture Engineering and its Application, 2018, pp. 165–168.
A. I. Pambudi, “Analisis Pengaruh Internal Geometri Terhadap Sifat Mekanik Material Polylactic Acid (PLA) Dipreparasi Menggunakan 3D Printing,” Tugas Akhir. Fakultas Teknologi Industri. Institut Teknologi Sepuluh Nopember: Surabaya, 2017.
D. T. Pham and R. S. Gault, “A comparison of rapid prototyping technologies,” Int J Mach Tools Manuf, vol. 38, no. 10–11, pp. 1257–1287, Oct. 1998, doi: 10.1016/S0890-6955(97)00137-5
“2713100032_Undergraduate Theses (1)”.
A. Aris Setiawan et al., “Optimasi Parameter 3D Printing Terhadap Keakuratan Dimensi dan Kekasaran Permukaan Produk Menggunakan Metode Taguchi Grey Relational Analysis,” 2018.
muhammad Rivaldi1, M. Y. (2023). Pengaruh Parameter Proses 3D Printing Terhadap Kuat Bentur. Jitt
Irfan Fadhil1, H. A. (2023). Optimasi Parameter Produk 3D Printing Terhadap Kekuatan Bending Dengan Menggunakan Filamen Nylon. jitt, 8.[4]
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Jurnal Inovasi Teknologi Terapan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.